![]() ![]()
USB Flashing Solved due to wrongly installed Flashing Cable Drivers on some configurations (i.e. Update cleanflight firmware on spf3 no boot pins code#XGold/Blackberry service is now also checked upon Blackberry tool startup, also after each Code calculation remaining Calculation Limit is displayed Default Security Area XGold Service count increased from 50 to 100 (100 phones limit between SA updates for Blackerry,XGold1.) Remaining XGold Credits are now shown upon launching of Nokia Tool (Those one used for XGold1 LBF, Blackberry Codes Service, etc) ![]() The supported MEP List are now acquired from box once Blackberry Tool launch Fixed DCT4 RPL Write problem when only DATA2 exists in RPL file Afterwards DCT4 Erase All chips, the Permanent Data aren't restored anymore Fixed bug with disappearing Tray icon after Minimize to Tray Fixed lots of Access Violatios after closing up Nokia Tool USB Connection Type is now selected automatically when XGold2 platform found Update cleanflight firmware on spf3 no boot pins plus#Dead-erased XGold2 flashing improved, plus added some messages regarding to reviving dead XG2 XGold1/2 Flashing Routines rewritten to be more memory effective Used to automatically generate FLASH IMEI DATA and programm it - one-click REPAIR ?4. Added "Auto-Rebuild IMEI" checkbox for "Read UEM IMEI" function. StatusBar messages are more accurate now Removed SuperDCT4 Activation from Credits Manager Removed DCT4 ASK-RPL From Credits Manager Fixed product mismatch on XG1/XG2 autodetection Fixed spurious XGold2 product to be displayed in XGold1/DCT4 tab If there is problems with autodetection - user still can select unlocking method manually. avoids RM-189 2310 problems avaiable on all boxes right now). Selftests moved to new "Diagnostic" module ![]() PMM Protection Checkbox added upon PM write. Added support for generating extended DCT4 RPL with Product Data for above models (CS problems) Added support for DCT4 (7250i, 6610i, 2125i, 2865i, 6275i) Product Data RPL Entity Writing for fixing CS Standalone DCT4 RPL Calculation Introduced, supported Asics: 2,5,6,7,11 Fixed invalid Calculation of Mastercode ![]() Old DCT4 Asic 2,5,6,7 Direct Unlock/Relock/Autolock Introduced, finally Dumped unique data might be lately used for USB operations if still FBUS operations fails. Use to boot phone by Flashbus directly, and dump Unique Data (for Simlock,SD.) when phone doesn't have correct BSI resistors value. BB5 Mass Memory Flashing Tested - Cyclone SW has this posibility from long time ago. C2-02 XGold2 Flashing "Added" - Cyclone has flashing compatibilty for this model, but MassMemory file couldn't be handled becasue too big. TX2 settings removed from BB5 Flashing Tab "Use OLD USB FLASHING METHOD" moved to BB5/Flashing tab Rapido Alive FUR-over-USB flashing not supported, flash those phones by Dead variant instead (Switch to RAW mode problem in this models.), or "Old USB Flashing Method" Certificates operations for Rapido FBUS-OVER-USB disabled, because is not supported by loaders ( it will fail without any attempt ) Added Dead USB Flashing for RAPIDO and other FUR-over-USB operations (DO NOT USE FOR CERTIFICATE READ/WRITE!), still "old method" avaiable in connection tab. Fixed problems with handling RAPIDO > v11.16.00 loaders over FBUS (FUR control Add Problem) New BB5 FBUS/USB Loaders v11.24.00 Introduced Update cleanflight firmware on spf3 no boot pins full#Full Erase for New Protocol APE phones fixed (wrong CMT Flash Device Index selected) PM Protection is automatically unticked during SX4 operations PM Protection is now unticked by default Introduced previous updates (standalone and free Broadcom unlocking, RAPUv21, etc) SE Xperia Unlocked introduced into installer, this is 3rd party addon 10 Cyclone credits = 1 Xperia phone unlocked Realtime SE Xperia Unlocker account Creator in 'Credits' tool added. BB5 FBUS/USB Loaders v11.40.00 Introduced ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |